How To Light A Coleman Stove
Troubleshooting a Lantern or Stove That Won't Low-cal
1 that fails to light can be very inconvenient, actually frustrating and sometimes fifty-fifty dangerous.
If you lot take an old stove or lantern that you just received or one that has been put away for an extended period of fourth dimension, please click here (for lanterns) or here (for stoves) before troubleshooting. Those instructions show you how to prepare a dusty erstwhile appliance for use. Stoves and lanterns with insect nests inside can be very dangerous.
Pressurized fuel is forced upward into the stove or lantern valve via a fuel tube. The valve passes the fuel to the generator where information technology is converted to a gaseous vapor. This vapor is sent to the burner and is ignited to produce a flame. This flame produces heat in a stove or incandesces a mantle on a lantern.
The problem of an appliance not lighting is ordinarily acquired by one of two things. Either the generator is chock-full-up with soot, or the fuel & air tube is blocked by dirt or varnish.
Lanterns. (go to stoves) Requite information technology 30 or 40 pumps to actually pressurize it well. If you accept a tip cleaner stem, turn it a few times and get out information technology down. If you don't have a tip cleaner stalk, cycle the valve on/off a few times.
Open the valve one full plough (or about 1/2 way on a mod lantern) and mind. 
You should hear air hissing at first, then a "spitting" sound in one case fuel is introduced to the generator.
1. If it does exactly what I depict in a higher place, the lantern is operating usually and should low-cal. If information technology is catching fire only never lights, y'all have a blockage in your burner. Please visit the "dirty lantern" instructions to make clean it.
2. If the hissing sound continues for more than than thirty seconds, open up the valve fully counterclockwise.
If the hissing continues, your fuel & air tube is nearly likely blocked.
If it starts spitting, the metering rod in your fuel & air tube has restricted movement and/or the return spring has complanate. Sometimes you lot can cure this by assuasive the lantern to run as the fuel passing through the arrangement will assistance clean it. If the spring is weak, you lot'll need to remove the fuel & air tube to stretch and/or clean it.
To larn how the fuel and air tube works please click hither. Instructions on how to remove the fuel & air tube are function of the rebuilding pages.
iii. If you lot do not hear annihilation, you are blocked somewhere, and nosotros need to detect out where. With the fuel valve turned off, use a wrench to loosen the jamb nut at the base of the generator nigh one full plow. Employ a rag to catch the fuel, then plough the fuel valve back on.
If fuel starts leaking from the base of the generator, the generator itself information technology plugged. I recommend y'all supplant it.
If nothing happens, your valve/fuel & air tube is completely blocked and you'll need to remove them. Instructions on how to remove them tube are function of the rebuilding pages.
Stoves. Take the tank out of the case and give it 30 or 40 pumps to actually pressurize information technology well. Rotate the lighting lever a few times and go out it pointing upwards.
Hold a rag in front end of the generator to grab any fuel that comes out. Open up the 
fuel valve slowly well-nigh one full plow and watch and mind. You should hear air hissing at first, then meet a stream of fuel shooting out the end of the generator.
1. If it does exactly what I describe above, the tank is operating properly and the stove should light. If it doesn't, there is a proficient chance that something is blocking the manifold and that can be extremely dangerous. Please visit the "dirty stove" instructions to clean information technology before continuing.
2. If you hear air coming out of the generator but do non see fuel flowing after about 15 seconds, spin the lighting lever around a few more times.
If fuel starts to come out you probably take a dirty fuel & air tube. It is possible that an extended burn down will assistance as the fuel passing through the system can clean it. But you might need to remove the valve and make clean it.
If fuel even so does not come out, the fuel & air tube is blocked.
To learn how the fuel & air tube works please click here. Instructions on how to remove the fuel & air tube are part of the rebuilding pages.
3. If you do not hear anything, you have a blockage somewhere and we need to discover out where. Turn the valve off and use a wrench to loosen the generator tube from the valve body. Plough the tube counterclockwise about three turns. Use a rag to catch the fuel and turn the valve dorsum on.
If fuel starts leaking out from this generator/valve connection, the generator itself it plugged. Click here to learn how to clean and/or replace a stove generator.
If cypher happens, your valve/fuel & air tube is completely blocked and you lot'll need to remove them. Instructions on how to do this are part of the rebuilding pages.
If you become stuck, you can send me an email to oldtowncoleman@gmail.com, or y'all can post your question on our Facebook page. Expert luck!
Did yous find this information useful? Click here to back up the Old Town Coleman Center with a cup of java!
Source: https://oldtowncoleman.com/learn/troubleshooting-coleman-wont-light.htm
0 Response to "How To Light A Coleman Stove"
Post a Comment